------------------------------------------------------------ ENGLISH VERSION (Die deutsche Version finden Sie unten) ------------------------------------------------------------ Gigaset S79H - Firmware update 05/2010 (version 78.036.04) ========================================================== How to update: -------------- 1. Please start the software "Gigaset Quicksync" on your PC. You will find it on the internet at http://gigaset.com/hq/en/cms/PageQuickSync.html 2. Please carry out the update of the Gigaset Quick Sync software if it is offered. 3. Remove the battery cover from your Gigaset S79H handset. 4. Connect the handset directly to your PC via a mini USB cable. (Do not connect the USB cable via a USB HUB to your PC; failures may occur). 5. Leave the batteries in the handset and switch the handset on. If necessary the device driver software of your handset will be installed automatically on your PC. 6. Choose “Connect handset automatically” in the Gigaset Quicksync window. 7. When a connection is set up, the message “S79H connected (n) (nnnnnnnnnn)” appears. If a new handset firmware is available, a prompt automatically appears. 8. The firmware will be installed on your handset in several cycles. Do not disconnect your handset until you see the message “Handset firmware has been updated successfully”. Improvements and changes: ------------------------- # Slideshow: The Screensaver menu has been extended by the function Slideshow. All pictures from the Screen-Saver folder are shown in idle mode one after the other. # keypad illumination: The brightness of the keypad illumination is now adjustable in 5 steps # 4 handsfree profiles: The handset now has 4 handsfree profiles: -Profile 1: Standard -Profile 2: For loud surroundings -Profile 3: Full duplex (only on a very good line) -Profile 4: Optimised for special connections Setting a handsfree profile in idle status, you can set various handsfree profiles to optimally adapt your to your environment. Profile 1 The optimum setting for most connectionsand set as default. Profile 2 Optimum volume in handsfree mode. However, this means that the participants cannot speak at the same time as the person speaking is given preferential transmission (making two-way conversations difficult). Profile 3 Optimises two-way conversations, both callers can hear each other, even if they talk at the same time. Profile 4 Optimised for special connections. If the default setting (profile 1) does not provide optimum sound,please give this a try. # additional display remark: If the display backlight is activated when the handset is not in the charger the customer is advised that this mode reduces the standby time significantly. # Deleting all appointments for one day: With this new option the customer can delete all appointments for 1 day. # picture CLIP with GAP bases: Picture CLIP is now supported on GAP bases. For other devices this depends on the software # Status display (e.g. AM1 = on ; INT 16) optimised # The character set position of "CR" and "Space" have been moved from key "1" to key "0" Descriptions for Firmware update: --------------------------------- # Pictures and ringtones stored on the handset should also be stored on the PC; these are deleted during an emergency update! # When updating SW do not connect the handset via the USB hub; please connect handset directly to the PC. ------------------------------------------------------------ DEUTSCHE VERSION ------------------------------------------------------------ Gigaset S79H - Firmware Update 05/2010 (Version 78.036.04) ========================================================== So erfolgt der Update: * Starten sie die Software „Gigaset Quicksync“ auf ihrem PC. Sie finden diese auf der Internetseite: http://gigaset.com/de/de/cms/PageQuickSync.html * Wird ihnen eine Aktualisierung angeboten, führen sie diese durch. * Nehmen sie den Akkudeckel von ihrem Gigaset S79H Mobilteil ab. * Verbinden sie das Mobilteil durch ein Mini-USB Kabel direkt mit ihrem PC (nicht mit einem USB-HUB) * Akkus bleiben im Mobilteil eingelegt; schalten sie das Mobilteil ein. Gegebenenfalls wird automatisch die Gerätetreiber Software für ihr Mobilteil installiert. * Wählen sie im Fenster der Gigaset Quicksync Software „Mobilteil automatisch verbinden“. * Bei bestehender Verbindung wird der Hinweis eingeblendet „Verbunden S79H (n) (nnnnnnnnnn)“. Steht eine neue Software zur Verfügung, erscheint automatisch die Aufforderung, dass die Firmware ihres Mobilteils aktualisiert werden kann. * Die Firmware wird in mehreren Zyklen auf ihrem Mobilteil installiert. * Trennen sie das Mobilteil erst nachdem sie den Hinweis „Mobilteil Firmware wurde erfolgreich aktualisiert“ erhalten haben. Verbesserungen und Änderungen: * Slideshow: Das Screensaver Menü wurde um die Funktion Slideshow erweitert. Alle Bilder aus dem Screen-Saver-Ordner werden im Ruhezustand der Reihe nach angezeigt. * Helligkeit Tastaturbeleuchtung: Die Helligkeit der Tastaturbeleuchtung ist jetzt in 5 Stufen einstellbar. * Freisprechprofile: Das Mobilteil verfügt jetzt über 4 Freisprechprofile: o Profil 1: Standard Profil. o Profil 2: für laute Umgebung. o Profil 3: Vollduplex ( nur an sehr guter Leitung ). o Profil 4: Problemanschluss Freisprechprofil einstellen: Sie können im Ruhezustand verschiedene Profile für das Freisprechen einstellen, um Ihr Telefon optimal an Ihre Umgebungssituation anzupassen. o Profil 1: Für die meisten Anschlüsse die optimale Einstellung, deshalb voreingestellt o Profil 2: Ermöglicht lautstärkenoptimiertes Freisprechen. Dies hat jedoch zur Folge, dass die Partner nacheinander reden müssen, da die sprechende Seite bevorzugt übertragen wird ( erschwertes Gegensprechen ). o Profil 3: Optimiert das Gegensprechverhalten - beide Seiten können sich verstehen, auch wenn sie gleichzeitig sprechen. o Profil 4: Optimiert auf spezielle Anschlüsse. Falls Profil 1 für Sie nicht optimal klingt, versuchen Sie es bitte hiermit. * Picture CLIP an GAP Basisstationen: Picture CLIP wird jetzt auch an GAP Basisstationen unterstützt. Nicht mit jeder Fremdgeräte Software möglich. * Statusanzeige: Die Darstellung der Statusanzeige (z.B. AB1 = ein ; INT 16) wurde optimiert. * Die Funktionen CR und Space wurden von Taste "1" zur Taste "0" verschoben Beschreibung SW-Update: * Selbsterstellte Bilder und Klingeltöne sollten Sie generell auf Ihrem PC sichern. Bei einem emergency update werden diese gelöscht! * Bei einem SW-Update des Mobilteiles, dieses nicht über einen USB-HUB anschließen, sondern direkt am PC.